My watch list

Siemens (unit)

The siemens (symbol: S) is the SI derived unit of electric conductance. It is named after the German inventor and industrialist Ernst Werner von Siemens, and is equivalent to the previously used designation of this unit, the mho. In English, the term siemens is used both for the singular and plural. The 14th General Conference on Weights and Measures approved the addition of the siemens as an SI derived unit in 1971.

This SI unit is named after Ernst Werner von Siemens. As with all SI units whose names are derived from the proper name of a person, the first letter of its symbol is uppercase (S). But when an SI unit is spelled out, it should always be written in lowercase (siemens), unless it begins a sentence or is the name "degree Celsius".

— Based on The International System of Units, section 5.2.

Additional recommended knowledge

Recognize and detect the effects of electrostatic charges on your balance

Guide to balance cleaning: 8 simple steps

Daily Visual Balance Check

Definition

SI multiples for siemens (S)
Submultiples			Multiples
Value	Symbol	Name	Value	Symbol	Name
10^–1 S	dS	decisiemens	10¹ S	daS	decasiemens
10^–2 S	cS	centisiemens	10² S	hS	hectosiemens
10^–3 S	mS	millisiemens	10³ S	kS	kilosiemens
10^–6 S	µS	microsiemens	10⁶ S	MS	megasiemens
10^–9 S	nS	nanosiemens	10⁹ S	GS	gigasiemens
10^–12 S	pS	picosiemens	10¹² S	TS	terasiemens
10^–15 S	fS	femtosiemens	10¹⁵ S	PS	petasiemens
10^–18 S	aS	attosiemens	10¹⁸ S	ES	exasiemens
10^–21 S	zS	zeptosiemens	10²¹ S	ZS	zettasiemens
10^–24 S	yS	yoctosiemens	10²⁴ S	YS	yottasiemens
Common multiples are in bold face.

For a physical object, typically an electronic device, with electrical resistance R, the conductance G is defined as

$G = \frac{1}R = \frac{I}V,$

where I is the current through the object and V is the voltage (electrical potential difference) across the object.

The unit siemens for the conductance G is defined by

$\mbox{S} = \Omega^{-1} = \dfrac{\mbox{A}}{\mbox{V}} = \dfrac{\mbox{C}^2 \cdot \mbox{s}}{\mbox{kg} \cdot \mbox{m}^2} = \dfrac{\mbox{A}^{2} \cdot \mbox{s}^3}{\mbox{kg} \cdot \mbox{m}^2}$

Note that the last term is in SI base units where A is the symbol for ampere, the unit of electric current; kg is the symbol for kilogram, the unit of mass; m is the symbol for metre, the unit of length; and s is the symbol for the time unit second. C is the symbol for the SI derived unit of electric charge, the coulomb; V is the symbol for the SI derived unit of voltage, the volt; and Ω is the symbol for the SI derived unit of electrical resistance, the ohm.

So for a device with conductance one siemens, then the electric current through it with one volt across it is one ampere, and for each extra volt across it the electric current through it increases by one ampere.

Example: The conductance of a resistor with resistance six ohms is G = 1/(6 Ω) $\approx$ 0.167 S.

Mho

The siemens is equivalent to the previously used term mho unit, which was derived from spelling ohm backwards and written with an upside-down capital Greek letter Omega: $\mho$ , Unicode symbol is U+2127 (℧). The term siemens, as it is an SI unit, is used universally in science and primarily in electrical applications, while mho is still used primarily in electronic applications. The upside down ohm symbol, while not an official SI unit, has the advantage of being less likely to be confused with a variable than the letter S when doing algebraic calculations by hand, where the usual typographical distinctions (such as italic for variables and Roman for unit names) are difficult to maintain. Furthermore, in some industries (like electronics) it is common to write the symbol for second incorrectly as S instead of s, causing potential confusion.

References

Brochure "The International System of Units" issued by the BIPM

Category: SI derived units

This article is licensed under the GNU Free Documentation License. It uses material from the Wikipedia article "Siemens_(unit)". A list of authors is available in Wikipedia.